latest news

/latest news
latest news 2019-10-15T03:03:59+00:00

Basic electronics fundamentals – Section – V

Basic electronics fundamentals - V The different types of ADC are successive approximation ADC, counter type ADC flash type ADC, integrator converters and voltage to-frequency converters. Stack is a sequence of RAM memory locations defined by the programmer. The program counter keeps track of program execution. To execute a program the starting address of the program is loaded in program. The PC sends out an address [...]

October 30th, 2019|Categories: Electronics|

Basic electronics fundamentals – Section – IV

Basic electronics fundamentals - IV Polling is a scheme or an algorithm to identify the devices interrupting the processor. Polling is employed when multiple devices interrupt the processor through one interrupt pin of the processor. The polling can be classified into software and hardware polling. In software polling the entire polling process is govern by a program. In hardware polling, the hardware takes care of checking the [...]

October 23rd, 2019|Categories: Electronics|

Basic electronics fundamentals – Section – III

Basic electronics fundamentals - III The CPU bus has multiplexed lines but the system bus has separate lines for each signal. (The multiplexed CPU lines are de-multiplexed by the CPU interface circuit to form system bus). The system clock is necessary for synchronizing various internal operations or devices in the microprocessor and to synchronize the microprocessor with other peripherals in the system. The direct data transfer [...]

October 22nd, 2019|Categories: Electronics|

Basic electronics fundamentals – Section – II

Basic electronics fundamentals - II A digit of the binary number or code is called bit. Also, the bit is the fundamental storage unit of computer memory. The 8-bit (8-digit) binary number or code is called byte and 16-bit binary number or code is called word. (Some microprocessor manufactures refer the basic data size operated by the processor as word). Bus is a group of conducting lines [...]

October 21st, 2019|Categories: Electronics|

Basic electronics fundamentals – Section – I

Basic electronics fundamentals - I It is a program controlled semiconductor device (IC}, which fetches, decode and executes instructions. The basic units or blocks of a microprocessor are ALU, an array of registers and control unit. The Software is a set of instructions or commands needed for performing a specific task by a programmable device or a computing machine. The Hardware refers to the components or [...]

October 17th, 2019|Categories: Electronics|

Basics of speakers

Basics of speakers Speakers are used you to listen to music on your phone, enjoy a film at the cinema or hear a friend’s voice over the phone. Basically speakers convert electrical signal into an audible sound, speakers contain an electromagnet, a metal coil which creates a magnetic field when an electric current flows through it. Inside a speaker, an electromagnet is placed in front of a permanent [...]

October 15th, 2019|Categories: Electronics|

How does continuity mode work in multimeter?

How does continuity mode work in multimeter? If there is very low resistance between two points, which is less than a few ohms, the two points are electrically connected and you’ll hear a continuous sound. This mode is also called as “diode mode”, “buzzer mode” If the sound isn’t continuous or if you don’t hear any sound at all, it means that what you’re testing has a faulty [...]

October 15th, 2019|Categories: Electronics|

Mobile Phone Repairing Tools and Equipment

We can see here some equipment’s and tools  for mobile service 1.Soldering Iron or Soldering Station: Used to Solder components 2. PCB Stand: Used to Hold PCB 3.Solder Wire (Lead): Used to Solder 4.IPA solution: Used to Clean PCB 5.Jumper Wire: Used to joint an One Point to another Point on aPCB 6.Blade Cutter: Used to Cut and Remove Lamination 7.Precision Screwdriver [...]

October 12th, 2019|Categories: Electronics|

Small intro about diodes

What is a Diode? A diode which passes only the electric current of a particular polarity from one side. This is used for rectification and switching.Several types of diodes are used in electronic instruments and gadgets. Chip diodes are used in mobile cell phones. Those are surface mount devices (SMD). Surface mount devices are soldered with special soldering technique Facts about Diodes Indicating in schematics of Diode: D or V or PD Function:ConvertingAC to [...]

October 8th, 2019|Categories: Electronics|

IPA Solution for hardware service

IPA Solution for hardware service Isopropyl alcohol (IPA) is one type of solution it is used for cleaning printed circuit boards (PCBs). It has some main advantages: It’s cheap IPA displaces water well, allowing surfaces to dry It removes ionic contamination. During water lock in mobile it will help more(we already uploaded how to fix water locked mobile like a professional) IPA has been [...]

September 23rd, 2019|Categories: Mobile Repairing tutorial|

Dead Mobile checking and fixing step by step

STEP BY STEP GUIDELINES Basically dead mobiles are called as not getting to turning on or not able to boot a mobile phone. STEP 1: Check battery. Most of the dead mobile phone problems are causes with battery and its performance.Approximately battery voltage is3.7v you can check this with using multimeter in voltage mode, if it is around 3.6v you can [...]

September 16th, 2019|Categories: Mobile Repairing tutorial|

How to Repair water lock Mobiles like a Professional

STEP BY STEP GUIDELINES If your mobile phone is dropped into water, it can have various problems like it may not power on (we called as dead mobile), it may restart sometimes, in some cases it produce overheat while normal usage (although it is normal in some models!), its battery may drain and discharge in quick, it may hang and freeze frequently [...]

August 26th, 2019|Categories: Mobile Repairing tutorial|

iPhone Soft Reset Process

STEP BY STEP GUIDELINES Simultaneously press and hold the Home button located at the center bottom of the iPhone and the Sleep/Wake button located at the top of the iPhone. Continue holding both buttons until the iPhone shuts down and again restarts. The process could take about 10 to 20 seconds. Once the iPhone shuts down, you can leave the buttons. After 10 [...]

September 20th, 2018|Categories: Common News|

Contact Info

Near Bus stand, KPN Building Upstairs, Mettur road, Erode.

Phone: 0424-4272224

Mobile: +91 9487230001

Web: Mathi Academy

Call Now Button